I like many here can recommend Prusa but honestly if you wanted to shop around this is the specs you are looking for:

Core XY is the new hotness thanks to Bamboo. But unless you want to print fast and loud a bed slinger still works.

What makes the biggest difference is the horned style and a direct drive printer is a game changer to print consistency. MK4s planetary gear is scary how much torque is in it but if you find any printer with a motor in its print head it’ll be worth it.

The other major improvement is auto bed levelling. Again Prusa’s nozzle solution is amazing, while magnets sensors are outdated but still works great if you printing on steel and the venerable plastic stick works but harder to recommend.

Finally magnetic sheets is a nice to have but finding a durable print bed like Garolite is better, just know that no one makes a Garolite bed so you’ll need to craft your own.

Other gimmicks you’ll find is ways to accelerate printing but I’ve honestly haven’t seen much improvement by using them and prefer the print quality when printing slower.

I think it’s limited in use but if you have a flat and thin stretch on your part, it could work.

So the whole process.

1. Print the first part, the first part has an interfacing slope which is 3d printer friendly. Which results in some stair stepping, but this time this is what we are trying to get.

2. Remove the first part from the print bed.

3. Start the second print.

4. Auto stop the second print after the first layer, and align it with the first print. The first print has a notch which is used to align the 2 parts.

5. Resume printing. The second print is design to print over air without supports, but with the first print in place it now prints on top of that and fuses the 2 parts together.

The reason I am doing this is so I can print parts which is larger than my print bed, without using fasteners or adhesive to bond them together. This method basically welds the parts together. This was just a small test print to prove the theory

Close

Yes I am trying to print 2 separate items, this was a test print but the idea would be a print larger than my print bed. I would use this to fuse them together.

The design isn’t the box but the interface. It’s a long slope which causes stair stepping. But while this is considered a defect I am using it to mate 2 parts. First is a slope which is printer friendly then an adjacent slope which would print in the air but I stop the print after the first layer so it’ll print ontop of the already printed part which I position after the first layer.

The models are designed in cad since this is going to be apart of a bigger part. Don’t want to share that yet because it’s not designed yet.

The parts are designed to fuse, that’s the point of this design. Again it’s designed for parts bigger than my print bed.

Of course, who else will I brag to 😛

Look closely in the middle and you will see a nook. That said the clear TPU is helping hide it

No noticeable difference between the TPU printed like it. I am sure if we had infill there would be more

CAD, got the parts designed up, then made 2 prints.

Print 1 is one half while print 2 I only printed the first layer. Aligned the 2 prints, then resumed printing.

I used magnets to hold the finished part down as to not move.

How does it feel to touch? It feels good it’s a bag. The plastic makes it feel stiff but yeah it’s nice.

Is it durable? No clue, feels like it is but I can’t tell until I’ve used it for a while. That said, the plastic nor the stitched edge on the plastic isn’t going to be the weakest link.

It’s the learning cad and having good special awareness which really benefits it. Not many others doing this

Added more photos to the post like this one

Added more photos to the post like this one

They are Polydry boxes. And I don’t dry by beads often enough. Though we haven’t hit summer yet here. So I can’t say how well they seal. Should be good though since my oldest box kept 15% all winter.

I think 40-50% we just got off winter

I am using PolyDryer Box from Polymaker, and the colored sackers are https://www.printables.com/model/865327-airlock-dock-stacker-for-polydryer

Other than that, nothing much other than an assortment of PETG.

I don’t care for the medium, I just want to watch my shows. In Canada we get basically the same shows as the US, but many are not available for streaming. So I want to watch Danny Phantom for example, I can’t. It’s not on any channel not streaming services.

And the same goes for dozens of other shows ranging from obscure like Martin Mystery to the ultra popular like The Fairly Odd Parents.

Heck even Disney doesn’t have everything.

DVD does and it cost less than most of these services.

Just tried it, worked to hold it in position for a bit. Fell apart once I started to use it mechanically.

The plastic is brittle. I think I’ll just delay the inevitable if I use super glue

There are some community prints like this. https://www.printables.com/model/194982-prusa-minimini-no-logo-frontrear-plate-with-honeyc

But I don’t know how brave I feel about taking it apart again.

DVD was to make a physical media of streaming content for a relative who doesn’t use technology but wanted to watch it. This would’ve been about 5 years ago ish since we don’t see them much anymore.

CD was about 3 years ago for my car since its head unit didn’t have car play. We’ve since purchased an iPod 7th gen to do the job.